The Atlas 9OHSC has single piece columns and extra long carriages to ensure years of trouble free service. The single piece columns require the customer to have a ceiling of at least 12 feet to stand up the column.
A single piece column coupled with the longer carriage offers unparalleled structural support for your types of lifting requirements.
The Atlas 9OHSC has single point lock release and chain-over-roller configuration. The Atlas 9OHSC has a low pad height to accommodate low riding vehicles. The Atlas 9OHSC has symmetrical arm configuration.
Benefits Of Our Atlas 9OHSC Overhead Two-Post 9000lb Capacity Carlift:
Chain-Over-Roller Cylinder Configuration
The Atlas 9OHSC has the chain-over-roller cylinder configuration. This above ground lift model that incorporate both the direct drive cylinder configuration and the chain-over-roller cylinder configuration. The base plate two post above ground lift implements the chain-over-roller configuration. This is the only hydraulic cylinder system that is possible in the base plate lift. The base plate two post above ground is designed for “low ceilings”. The direct drive hydraulic cylinder configuration cannot be used in the base plate lift because the hydraulic cylinder would extend above the 9’ 3” column when the lift arms were raised to the maximum height. The “overhead” two post above ground lift may incorporate either the direct drive hydraulic cylinder or the chain-over-roller hydraulic cylinder.
Includes Three Piece Truck Adapter Set
The included truck adapters add even more lifting height to the Atlas 9OHSC. The Atlas 9OHSC comes with a three piece truck adapter which offers many more lift height combinations than standard two piece truck adapter sets.
Single Point Lock Release
The Atlas 9OHSC has single point release which makes it easy for the operator to unlock both column locks from one column.
Overhead Bar Configuration
The overhead bar configuration of the Atlas 9OHSC leaves the area between the columns open, and allows the operator to easily roll a transmission jack or a tool box under the car.
Symmetric Columns
The symmetric column design provides a very wide drive through area to accommodate dual wheel pickups.
Single Piece Columns And Extra Long Carriages
The Atlas 9OHSC incorporates a single piece 11’ 10” formed column and an extra long carriage that provides maximum column and arm strength to lift and support a 9,000 lb. vehicle.
Rubber Covers
Rubber covers on the carriages help to prevent door damage.
Padded Automatic Shut-Off Bar
The padded shut-off bar located below the cross beam prevents the top of the vehicle from being damaged by hitting the cross beam. The padded bar, when contacted, automatically shuts off the motor on the power unit to prevent the vehicle from being lifted.
Packaging
The Atlas 9OHSC cannot be hauled in the back of a pickup truck. The single piece columns are almost 12 feet long. Please bring a trailer or a long bed roll back truck when you pick up the Atlas 9OHSC from the warehouse or shipping terminal. Electrical Requirement The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended. Installation Most of our above ground lift customers install their own car lifts. The average time to install the Atlas 9OHSC car lift is four hours. We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.
Specifications**NOTE: Specifications are subject to change without notice.
Highlights
9,000 LB. Capacity
Super Symmetric Arms
Symmetric Columns
Atlas Powder Coat Finish
“Padded” Shut-Off Bar
Clear Floor Design
Single Point Lock Release
Dual Hydraulic Chain-Drive Cylinders
Automatic Arm Restraints
Mounting Hardware Included
Free 12 Piece Truck Adapter Set
5 Year Structural Warranty, 1 Year Hydraulic Cylinder Warranty, and 1 Year Power Unit Warranty
Shipping Weight: 1,404 lbs.
Specifications
Capacity 9,000 LB.
Overall Height 142″ (11’ 10″)
Overall Floor Width 133 1/2″ (11’ 1 1/2″)
Outside Column to Outside Column 125 1/2″ (10’ 5 1/2″)
Maximum Lift Height (Without Adapters) 76 3/4″
Maximum Lift Height (With Adapters) 87 3/4″
Minimum Arm Height 4″
Inside Column 109 1/2” (9’ 1 1/2”)
Drive Thru 100 1/2” (8’ 4 1/2”)
Column Size 8″ x 9 3/8″
Column Thickness of Steel 5mm
Base Of Lift 16 3/4″ x 17 3/4″
Motor/Electrical Requirement 220 volt single (1) phase.
A 30 amp breaker is recommended
Oil Requirement 3-5 Gallons AW32/AW46 (NOT INCLUDED)
Shipping Weight 1,430 LBS.
Adapter Heights 4 Each 2”, 3”, 6”
Arm Hole/Adapter Peg Size 1.5”
Requires a minimum of 4″ of concrete with a 3000 psi. rating
Reviews
There are no reviews yet.