The Atlas OH-10X has single piece columns and extra long carriages to ensure years of trouble free service. The single piece columns require the customer to have a ceiling of at least 13 feet to stand the column.
A solid column coupled with the longer carriage offers unparalleled structural support for all types of lifting requirements.
Benefits Of Our Atlas OH-10X Two-Post 10000lb Capacity Carlift
Direct Drive Cylinders
Extra long direct drive cylinders in each column allows the Atlas OH-10X to lift vehicles several inches HIGHER than many other lifts on the market. If you are over 77″ tall, then this extra lifting height makes it much easier for you to walk under the vehicle.
Rubber Covers
Rubber covers on the carriages help to prevent door damage.
Padded Automatic Shut-Off Bar
The padded shut-off bar located below the cross beam prevents the top of the vehicle from being damaged by hitting the cross beam. The padded bar, when contacted, automatically shuts off the motor on the power unit to prevent the vehicle from being lifted.
Packaging
The Atlas OH-10X cannot be hauled in the back of a pickup truck. The single piece columns are almost 13 feet long. Please bring a trailer or a long bed roll back truck when you pick up the Atlas OH-10X from the warehouse or shipping terminal.
Includes Three Piece Truck Adapter Set
The included truck adapters add even more lifting height to the Atlas OH-10X. The Atlas OH-10X comes with a three piece truck adapter which offers many more lift height combinations than standard two piece truck adapter sets
Single Point Lock Release
The Atlas OH-10X has single point release which makes it easy for the operator to unlock both column locks from one column.
Overhead Bar Configuration
The overhead bar configuration of the Atlas OH-10X leaves the area between the columns open, and allows the operator to easily roll a transmission jack or a tool box under the car.
Symmetric Columns
The symmetric column design provides a very wide drive through area to accommodate dual wheel pickups. The Atlas OH-10X cannot be hauled in the back of a pickup truck. The single piece columns are almost 13 feet long. Please bring a trailer or a long bed roll back truck when you pick up the Atlas OH-10X from the warehouse or shipping terminal.
Single Piece Columns And Extra Long Carriages
The Atlas OH-10X incorporates a single piece 12′ 7″ formed column and an extra long carriage that provides maximum column and arm strength to lift and support a 10,000 lb. vehicle.
Electrical Requirement
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.
Installation
Most of our above ground lift customers install their own car lifts. The average time to install the Atlas OH-10X car lift is four hours. We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.
Highlights
10,000 lb. capacity
Inside Column Width: 117 1/2″ (9′ 9 1/2″)
Direct Drive Cylinders
Symmetric Columns
Heavy Duty 2 Stage Symmetric Arms
Automatic Arm Restraints
Overhead Design
Single Point Lock Release
Atlas Powder Coat Finish
Mounting Hardware Included 5 Year Structural Warranty, 2 Year Hydraulic Cylinder Warranty, and 1 Year Power Unit Warranty
Free 12 Piece Truck Adapter Set
Shipping Weight: 1,665 lbs.
Specifications
Capacity 10,000 LB.
Overall Height 152″ (12’ 8”)
Overall Floor Width 144 3/8″ (12’ 3/8″)
Outside Column to Outside Column 136″ (11’ 4″)
Maximum Lift Height (Without Adapters) 74 3/4″
Maximum Lift Height (With Adapters) 85 3/4″
Minimum Arm Height 4 1/2″
Inside Column 118 1/4” (9’ 10 1/4”)
Drive Thru 106 7/8” (8’ 10 7/8”)
Column Size 9 1/8″ x 11″
Column Thickness of Steel 5mm
Base Of Lift 18 1/2″ x 21 1/2″
Motor/Electrical Requirement 220 volt single (1) phase.
A 30 amp breaker is recommended
Oil Requirement 3-5 Gallons AW32/AW46 (NOT INCLUDED)
Shipping Weight 1,665 LBS.
Adapter Heights 4 Each 2”, 3”, 6”
Arm Hole/Adapter Peg Size 1.5”
Requires a minimum of 4″ of concrete with a 3000 psi. rating
Reviews
There are no reviews yet.