ATLAS PV-15P 2 Post Overhead Lift (15,000lbs Capacity) Professional Value

Benefits Of Our Atlas PV-15P Two-Post 15000lb Capacity Carlift

Symmetrical Columns And Arms
The Atlas PV-15P two post above ground lift has symmetrical columns and symmetrical arms to allow easy access to the widest of vehicles.

Direct Drive Cylinder Configuration
The Atlas PV-15P has the direct drive cylinder configuration. This above ground lift model incorporates both the direct drive cylinder configuration and the chain-over-roller cylinder configuration.

The base plate two post above ground lift implements the chain-over-roller configuration. This is the only hydraulic cylinder system that is possible in the base plate lift. The base plate two post above ground is designed for “low ceilings”. The direct drive hydraulic cylinder configuration cannot be used in the base plate lift because the hydraulic cylinder would extend above the 9′ 3″ column when the lift arms were raised to the maximum height.

The “overhead” two post above ground lift may incorporate either the direct drive hydraulic cylinder or the chain-over-roller hydraulic cylinder.

Electrical Requirement:
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.

Installation:
The Atlas PV-15P above ground lift should be installed on a concrete floor. This concrete floor should have a minimum of six (6) inches of concrete with 3000 PSI strength. Most of our above ground lift customers install their own car lifts. The average time to install the Atlas PV-15P car lift is five hours.

We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.

Highlights

15,000 LB. Capacity
Symmetric Arm Design
Commercial Grade
Automatic Arm Restraints
Powder Coat Powder Coat Finish
Single Point Lock Release
Clear Floor Design
“Padded” Shut-Off Bar
Adjustable To Three (3) Heights: 12′ 6 3/8″ (Requires The Purchase of Additional Shorter Cables), 13′ 6 3/8″, and 14′ 9 3/8″
Free 12 Piece Truck Adapter Set
Anchor Bolts Included
Shipping Weight: 2,518 LBS.
Specifications

SET-UP LOW MIDDLE HIGH
Capacity 15,000 LB.
Lifting Time Ask Your Salesperson
Overall Height 150 3/8″ (12′ 6 3/8″)* 162 3/8″ (13′ 6 3/8″) 177 3/8″ (14′ 9 3/8″)
Height To Shut Off Bar 140 3/4″ (11′ 8 3/4″)* 152 3/4″ (12 8 3/4″) 167 3/4″ (13′ 11 3/4″)
Overall Width 158″ (13′ 2″)
Overall Width
(Without Motor) 150 ¼” (12′ 6 ¼”)
Maximum Lift Height 69 1/8″ (5′ 9 1/8″)
Maximum Lift Height
(With Truck Adapters) 79 3/4″ (6 7 3/4″)
Minimum Pad Height 6 5/8″
Between Columns 122 7/8″ (10′ 2 7/8″)
Column Size 14 3/8″ x 7 3/4″
Column Thickness of Steel 6mm
Carriage Thickness of Steel 6mm
Arms Thickness of Steel 6mm
Drive Thru 109″ (9′ 1″)
Base of Lift 17 ½” x 20 ½”
Cable Diameter .375″
Motor/Electrical Requirement 4 HP, 220V +/- 5% (209-231volts) single (1) phase.
A 30 amp breaker is required.
Oil Requirement 3-5 Gallons AW32/AW46
Outside Column to Outside Column 138 3/4″ (11′ 6 3/4″)
Shipping Weight 2,518 LBS.
*Requires the purchase of additional shorter cables.
Requires a minimum of 6” of concrete with 3000 psi.