The PCL-18B is a set of two mobile lift systems with a total lifting capacity of 36,000 lbs. It is designed for use in automotive workshops and garages for vehicle maintenance and repair. The lift operates using a hydraulic system powered by an electric motor that requires a power source of 208-230-190V, 50-60 Hz, and 3 Ph. The mobile design allows for easy transport from one location to another, making it ideal for use in garages, driveways, and workshops. The set of two lifts provides a quick and convenient way to lift and support vehicles for maintenance and repair purposes, and the 36,000-lb capacity ensures that the lift can handle a wide range of vehicles, including cars, trucks, and SUVs. The PCL-18B is durable, reliable, and ideal for use in commercial settings where heavy vehicles need to be lifted and maintained.
Features
- 18,000-lb. individual column capacity / 108,000-lb. maximum system capacity
- Meets or exceeds the standards prescribed by ANSI/ALI ALCTV-2011
- Two, four, or six column configurations can accommodate heavy duty trucks and light duty passenger vehicles
- 208-240V, 3-PHASE MAIN POWER SYSTEM – optional voltages available upon request*
- SINGLE, PAIR or TEAM operation
- For a standard four-column set, just three 30′ cables are used leaving the front or back of the lift clear of cable obstructions
- Simple operation, long service life and minimum maintenance
- Intuitive controls allow the lift to be fully programmed and controlled from any column
- Control systems feature 24-volt safety circuitry
- The PLC and main system components are standard off-the-shelf brands rather than proprietary printed circuit boards or controls, which can be very expensive to service or replace
- Smart electronics feature self-diagnostics and self-calibration functions
- Sealed and enclosed linear potentiometers feature precision potentiometric output and high-frequency response for precise synchronization and communication of all columns throughout all operation cycles for precise, level lifting
- Variable height limit settings can be programmed for shops with low ceilings or when specific vehicle service requirements necessitate specific rise heights
- Two-speed lowering option – turtle or rabbit speed settings
- Each column is equipped with a warning light and audible alarm for critical warning alerts
- Emergency shut-off switches on each column quickly shut off power to the lift in the event an unsafe condition is detected by the operator
- Separate key lock enclosure on each column
- Electronics are multi-fuse protected
- An enclosed electric-hydraulic power system that ensures quieter operation is better suited for sound-sensitive areas
- Pallet-jack style steering wheels enable the columns to be lowered firmly on the floor vs. constantly loaded spring-type steering wheels that can cause columns to roll when unladen by the weight of a vehicle
- Low-mounted power units and cylinders means a lower center of gravity, making the columns easier to move and less likely to topple vs. screw-drive systems with heavy overhead motors and drive systems
- Extended forks accommodate wide tires and deep wheel configurations
- Multi-width wheel forks with locking pins accommodate the widest range of wheels, eliminating the need for specialty wheel adapters
- Tandem 8” diameter polyurethane covered steel wheels with sealed roller bearings easily roll over dirt and debris
- Heavy-duty steel carriage rollers feature turned, ground and polished axle pins
- Manual safety override valves on each column permit the lift to be lowered in the event of a power outage without the need for manual hand cranks
- Durable forklift pockets provide simplistic handling when moving the lift columns from one facility to another
- Inverted hydraulic cylinders feature an integrated safety valve to prevent accidental uncontrolled lowering in the event of oil pressure loss
- Multiple, automatic, independent safety locks spaced every four inches ensure safe operation
- Space-saving design, reduced column weight and a tight turning radius provides improved mobility
- Use the lift to place vehicles on tall jack stands then use the columns to raise another vehicle in an adjoining bay
- Durable powder coat finish
Specification
Lifting Capacity 18,000 lbs. (8,165 kg)
A – Overall Height (RAISED) 101” (2,565 mm)
B – Overall Height (LOWERED) 146.5” (3,721 mm)
C – Max. Lifting Height 71.5” (1,889 mm)
D – Overall Depth 48.75” (1,238 mm)
E – Overall Width 45” (1,143 mm)
F – Chassis Length 32.25” (819 mm)
G – Min. Lifting Fork Width 9.5” (241 mm)
H – Max. Lifting Fork Width 35” (889 mm)
I – Lifting Fork Length 11.5” (292 mm)
Power System (Motor) 208-240V, 3-Phase
Turning Circle Turning Circle
Column Weight 1,450 lbs. (657 kg)
Lifting Speed 85 sec
Shipping Weight per Column :1,450 lbs. (657 kg)
Shipping Dimensions per Column :106” x 55” x 41” (2,696 mm x 1,397 mm x 1,041 mm)
